Dongguan Hangong Technology Co., Ltd. continuously introduces the most advanced international technology, keeps pace with the times, and constantly innovates to make its products invincible in the professional market. And established a good reputation in the industry! The company's products have the characteristics of high quality and low price, with advanced production technology and optimized human resources, to create first-class automation equipment. Provide customers with high-quality after-sales service in a timely manner. The company adheres to the corporate philosophy of "integrity", "innovation" and "quality", creates a brand with integrity, seeks innovation with technology, and seeks development with quality. We sincerely hope to cooperate with friends from all walks of life for common development.

Here are some common troubleshooting methods for common automatic wire stripping machines, and I hope to help you.

Thread can't be stripped

1. Check the cutting depth of the wire and adjust the wire diameter value to decrease.

2. The gap of the incoming transmission wheel is too large, adjust the gap of the incoming transmission wheel.

3. Whether the stripping head setting is greater than 2mm.

4. There is dirt in the inlet pipe.

5. The tool retract setting is too large and needs to be reduced.

The tail can't be stripped

1. Check the cutting depth of the wire and adjust the wire diameter value to decrease.

2. The gap of the incoming transmission wheel is too large, adjust the gap of the incoming transmission wheel.

3. Whether the stripping head setting is greater than 2mm.

4. The tool retraction setting is too large and needs to be reduced.

Thread skin crush

1. Adjust the gap between the incoming transmission wheel and the outgoing transmission wheel.

2. Contact the factory to replace the transmission wheel

The core is cut

1. Increase the value of the wire diameter until it is suitable (the best position is when the blade has just cut through the thread skin but cannot damage the wire core).

2. If the wire skin is very thin, and it is found that the wire cannot be stripped after adjusting the wire diameter, the knife withdrawal value can be appropriately reduced.

Different lengths, the actual line length of the outgoing line is greater than or equal to the set line length

1. The gap of the incoming transmission wheel is too large, and sometimes the end of the thread cannot be stripped, and the line that cannot be stripped is greater than the set line length. Adjust the "incoming gap adjustment wheel" to increase the pressure.

2. There is dirt in the inlet pipe, please check and clean it properly.

3. Adjust the pressure of the incoming transfer wheel.

The length is different, the actual line length is less than or equal to the set line length

1. The wire itself varies in thickness.

2. The scroll wheel has dirt and needs to be cleaned. There is wax on the surface of the wire, which causes the in and out wire transmission wheel to slip.

3. Take out the line, set the program to "00", dry run, stop, and check whether the "inlet and outlet wheel" rotates flexibly or is stuck.

4. The pay-off rack is stuck, causing the input line to slip

Part of the core is too long

1. The wire diameter is too small, the knife is cut to the wire core, and it is taken out when stripping. The wire diameter needs to be increased by 1-2

2. The tool retract setting is too small, and the tool retract parameter should be increased appropriately

Sometimes the wires are connected together without cutting

1. Add oil to the active part of the knife edge and try again (generally every 2 hours of operation)

2. Reduce the speed and try again.

3. Check whether the specification of the wire is within the allowable range of this model.

4. Is the blade dull?

Incision inclines when tangent

1. The wire itself is too bent and needs to be straightened.

2. The wire mouth is not facing the center of the knife edge

The company specializes in manufacturing I-PEX terminal machines, coaxial wire stripping machines, RF antenna machines, small coaxial wire precision stripping semi-automatic wire stripping machines, and coaxial wire automatic wire stripping machines. Coaxial end machines (applicable to I-PEX, RF, and other series terminals) and various wireless antenna (RF) product processing equipment and fixtures. At the same time undertaking the development of various non-standard equipment. SMD electronic parts packaging machine, carrier tape forming machine and other mechanical products are welcome to call to consult and purchase.